"b610-06-070-06 jmc steel group"

4 Inch Octagon Box, 1-1/2 Inch Deep, Side Knockouts: (1) 1/2 Inch, End Knockouts: (1) 1/2 Inch, Side Knockouts: (5) 1/2 Inch Cubic Inches: 15.8, Drawn, Steel

Category: Octagon Metallic Boxes

OTV 163 W STEEL MSGNR GENERAL CABLE 00.41JO.27534 16/3 W/STEEL MESSENGER

24" Steel Pipe Wrench, 3" Jaw Capacity, OVERBITE JAW™ Allows for Largest Gripping Surface, Dual Coil Springs, Ergonomic Handle Design

Category: Pipe Wrenches

Reducing Bushing, Threaded, 1 x 3/4 Inch, Steel, For Use With Rigid/IMC Conduit

Category: Steel Reducing Bushings

Wall Mount Enclosure, NEMA 4X, Hinge Cover With Additional Quarter Turn Latches, 48 x 36 x 10 Inch, Stainless Steel 304

Category: Stainless Steel Wall Mount Enclosures

Cabinets provide outdoor protection for instrument current transformer required in watt-hour metering. This CT Cabinet 2-Door with Steel Foot-Mount Panel Type 3R, A484814CTAUE item measures 48x48x14in with a material of Steel colored Gray.

Category: Current Transformer Hinged Cover Enclosures

3-Gang, 2-Toggle 1-Duplex Device Combination Wallplate, Standard Size, 302 Stainless Steel, Device Mount - Stainless Steel.

Category: Toggle Switch / Duplex Receptacle Combination Wallplates

Liquidtight Strain Relief Cord Connector, Straight, 3-1/2 Inch, Cable Range 3.00 - 3.390 Inch, Steel, For Use in Wet or Dry Locations

Category: Straight Steel Cord Grips

EMT Conduit Strap, 1-Hole, 3/4 Inch, Steel With Zinc Finish, For Use With EMT Conduit

Category: Steel 1-Hole Conduit Straps

Hex Nut, Stainless Steel Construction, 5/8 Inch-11

Category: Stainless Steel Hex Nuts

Threaded Conduit Nipple, 1-1/4 Inch x Close, Stainless Steel

Category: Stainless Steel Conduit Nipples

Conduit Locknut, 4 Inch, Threaded, Steel, For Use With Rigid/IMC Conduit

Category: Steel Conduit Locknuts

2-gang No Device Blank Wallplate, Standard Size, 302 Stainless Steel, Strap Mount, - Stainless Steel

Category: 2-Gang Blank Wallplates

Square Box Cover, 4 Inch Square x 1 Inch Raised, Pre-Galvanized Steel, Center Blanked with Tapped Ears on 2-23/32 Inches Centers

Category: 4" Square Metallic Box Fixture Covers

2-Gang, Steel Toggle (1) and Duplex Receptacle Cover, Fits FS and FD Type Boxes, Furnished with Stainless Steel Screws without a Gasket.

Category: Steel FS & FD Device Box Covers

EMT Compression Coupling, 3/4 Inch, Material: Steel, For Use With EMT Conduit

Category: Steel Concrete Tight EMT Compression Couplings

Handy Box, 1-1/2 Inch Deep, Side Knockouts: (3) 1/2 Inch, End Knockouts: (1) 1/2 Inch, Bottom: (2) 1/2 Inch, Cubic Inches: 10.3, Drawn, Steel

Category: Metallic Handy Boxes

Combination Coupling, EMT Compression to Rigid Threaded Conduit, 3-1/2 Inch Diameter, Steel With Zinc Chromate Finish

Category: Steel Rigid To EMT Combination Couplings

Wall Mount Enclosure, NEMA 4X, Continuous Hinge Cover With Clamps, 24 x 16 x 8 Inch, Quarter Turn Latch, Stainless Steel

Category: Stainless Steel Wall Mount Enclosures

Deep Strut with Slots, Type 316 Stainless Steel, 1-5/8" x 7/8" x 10'

Category: Stainless Steel Strut with Slots

Liquidtight Strain Relief Connector, 1/2 Inch, Straight, Cord Range 0.125 to 0.375 Inch, Throat Diameter 9/16 Inch, Steel Body, Glandnut, and Grip, Rubber Bushing

Category: Straight Steel Cord Grips

Fender Washer, Stainless Steel, 1/2 x 2 Inch

Category: Stainless Steel Fender Washers

Wide Range Cord Grip, Dust Tight Strain Relief, Straight Male, Insulated, Galvanized Steel Grip, Thread Size: 3/4 Inch NPT, Cable Diameter: 0.520 Inch - 0.730 Inch.

Category: Single / Double Weave Strain-Relief Grips