"polaris it-4"

Short Barrel Copper Lug, one hole with peep hole, wire range of 6 AWG. Produced from high conductivity copper tubing. Allows easy inspection of the termination to assure complete cable insertion. Marked with die index and color coded blue. cULus Listed for 35KV maximum when properly installed.

Category: 1-Hole Copper Compression Lugs

Easy-Splice Heat Shrinkable End Cap 4/0 AWG - 750 MCM These caps replace greases, tapes, epoxy, encapsulation, or dips. In most sizes, installation may be accomplished in less than one minute. Heat-shrinkable end caps provide for efficient and positive cable end sealing. Made of thermally stabilized polyolefin, the interior of the HSC is coated with a meltable sealant to assure a watertight seal, complete insulation, abrasion and corrosion resistance. Seals may be affected over lead, steel, aluminum, copper and all standard plastic and elastomeric insulating materials and conduit. HSC end sealing caps are qualified to ANSI C119.1-1986 and rated to ICEA electrical withstand test for 1,000 volts. HSC end sealing caps can be used as a live seal for cables carrying up to 1,000 volts. They can also be used as end seals for storing and pulling de-energized cable.

Category: Heavy Wall Heat Shrink

2 Port Aluminum Dual Rated Transformer Stud Connector 500 MCM - 4 AWG Aluminum dual rated transformer stud connectors are versatile and reusable set screw connectors made from 6061T-6 aluminum alloy for superior electrical and mechanical performance. Clear plated for low contact resistance- stud is tin plated copper which provides low contact resistance for connection to transformer. For use with copper and aluminum conductors. Meets or exceeds ANSI C119.4 Class A. Rated 600V. Temperature rating 90 degrees C.

Category: Transformer Lug Kits

NSI VM-A-11 VOLTAGE MARKERS 4

Category: Voltage Markers

3 Port Heavy Duty Dual Rated Transformer Lug 350 MCM - 6 AWG Heavy Duty Dual Rated Transformer Lugs are versatile and reusable set screw connectors made from high strength 6061-T6 aluminum alloy for superior electrical and mechanical performance. Two set screws per wire hole ensure an exceptional connection. Electro-tin plated for low contact resistance. For use with copper or aluminum conductors. Mounting hole spacing is NEMA 1-3/4". Meets or exceeds ANSI C119.4 Class A. Rated 600V. Temperature rating 90 degrees C.

Category: 3-Conductor Aluminum Mechanical Lugs

120-480V 50/60 Hz 15 amp maximum receptacle with 3 colorcoded 12” long, #14 power leads and 4 color-coded 12” long, #18 signal leads.

Category: Photo Control Accessories

NSI 1036 225A 4-14 AWG 36 CIR

Category: Load Center Neutral & Ground Bars

NSI ISE167 "4/0 - 2/0 STR INS

Category: Standard Barrel Aluminum Compression Sleeves

NSI G-2-S "BRONZE GROUND CLAM

Category: Bare Wire Ground Clamps

NSI VM-B-36 VOLTAGE MARKERS

Category: Voltage Markers

Nsi Bs400t2 Dual Range Lug two 250 Mcm- 1/0 Or Four 250 Mcm- 1/0

Category: 1-Conductor Aluminum Mechanical Lugs

Premium 070 Electrical Tape Yellow, 3/4" X 66 Ft, -18 to 105c, 7mil, 600v, UL CSA

Category: Color Coding Tape

NSI L214P #2 AWG MAX WIRE SIZ

Category: 2-Hole Long Barrel Copper Compression Lugs

Vinyl Insulated Spade, 22-18 AWG, 1/4"Stud, 300 Volt, Red, 100 Per Pack

Category: Vinyl Insulated Block Fork Terminals

NSI L2N-14P #2 AWG MAX WIRE S

Category: 2-Hole Long Barrel Copper Compression Lugs

NSI VM-B-5 VOLTAGE MARKERS 22

Category: Voltage Markers

NSI S12-14N 12-10 AWG NYLON I

Category: Nylon Insulated Standard Fork Terminals

NSI VM-B-3 VOLTAGE MARKERS 12

Category: Voltage Markers

NSI AL300N 300 MCM ALUM COMPR

Category: 2-Hole Aluminum Compression Lugs

NSI PC4030-LS-W 4 X 3 LOK-SLO

NSI CB75WH 3/4" CONDUIT BENDE

NSI 6TB 4-4AWG

NSI PC2040-LSN 2 X 4 LOK-SLOT