"it-4"

Short Barrel Copper Lug, one hole with peep hole, wire range of 6 AWG. Produced from high conductivity copper tubing. Allows easy inspection of the termination to assure complete cable insertion. Marked with die index and color coded blue. cULus Listed for 35KV maximum when properly installed.

Category: 1-Hole Copper Compression Lugs

Easy-Splice Heat Shrinkable End Cap 4/0 AWG - 750 MCM These caps replace greases, tapes, epoxy, encapsulation, or dips. In most sizes, installation may be accomplished in less than one minute. Heat-shrinkable end caps provide for efficient and positive cable end sealing. Made of thermally stabilized polyolefin, the interior of the HSC is coated with a meltable sealant to assure a watertight seal, complete insulation, abrasion and corrosion resistance. Seals may be affected over lead, steel, aluminum, copper and all standard plastic and elastomeric insulating materials and conduit. HSC end sealing caps are qualified to ANSI C119.1-1986 and rated to ICEA electrical withstand test for 1,000 volts. HSC end sealing caps can be used as a live seal for cables carrying up to 1,000 volts. They can also be used as end seals for storing and pulling de-energized cable.

Category: Heavy Wall Heat Shrink

6 Wire Polaris 250 MCM-6 AWG Uninsulated Multi-Cable Connector Polaris Uninsulated Multi-Cable Connectors are made from 6061-T6 aluminum alloy and are plated for corrosion resistance. They are stacked in one hole increments, up to 14 holes and are suitable for use on wire from #4 AWG to 750 MCM. UL Listed 486B Wire Connector. AL9CU. Rated 600V, 90 degrees C. Dual rated for use with copper and/or aluminum cables. Not recommended for fine-stranded, flexible wire.

Category: Non-Insulated Multi-Tap Connectors

Bare Ring Terminal, 22-18 AWG, 1/4" Stud, 600 Volt, Silver, 100/Pack

Category: Nylon Insulated Ring Tongues

Vinyl Insulated Spade, 12-10 AWG, 1/4" Stud, Small, 300 Volt, Yellow, Pack Of 12

Category: Vinyl Insulated Standard Fork Terminals

Nylon Insulated Ring Terminal, 7 AWG, 1/4? Stud

Category: Nylon Insulated Ring Tongues

NSI FTH5A-D ADHESIVE TIE MOUN

Category: Cable Tie Bases

Voltage Markers 240 Volts, 4ea. 4.5x1.125"

Category: Voltage Markers

NSI L20N-14P #2/0 AWG MAX WIR

Category: 2-Hole Long Barrel Copper Compression Lugs

Vinyl Insulated Ring, 12-10 AWG, 1/4" Stud, 300 Volt, Yellow, 500 per Pack

Category: Vinyl Insulated Ring Tongues

NSI S22-4N 22-18 AWG NYLON IN

Category: Nylon Insulated Standard Fork Terminals

Copper Compression Lug, Conductor Size: 1/0 AWG, 2-Hole Stud, Long Barrel, Stud Diameter: 1/4".

Category: 2-Hole Long Barrel Copper Compression Lugs

Vinyl Insulated Ring, 12-10 AWG, 1/4" Stud, 300 Volt, Yellow, Small Pack of 20

Category: Vinyl Insulated Ring Tongues

Nylon Ring Terminal, 22-18 AWG, #4 Stud, Red, 100/Pack

Category: Nylon Insulated Ring Tongues

NSI CTH-4040 COPPER C TAP 3/0

Category: C-Tap Press-On Lugs

Vinyl Insulated Ring Terminal, 16-14 AWG, 1/4" Stud, 300 Volt, Blue, 70 Piece Pro Pack

Category: Vinyl Insulated Ring Tongues

8 Wire Polaris 250 MCM-6 AWG Uninsulated Multi-Cable Connector Polaris Uninsulated Multi-Cable Connectors are made from 6061-T6 aluminum alloy and are plated for corrosion resistance. They are stacked in one hole increments, up to 14 holes and are suitable for use on wire from #4 AWG to 750 MCM. UL Listed 486B Wire Connector. AL9CU. Rated 600V, 90 degrees C. Dual rated for use with copper and/or aluminum cables. Not recommended for fine-stranded, flexible wire.

Category: Non-Insulated Multi-Tap Connectors

10 Sol - 2/0 Str Economy 360 Degree Hub for Ground Clamps Threaded hub cast of high-strength, highly conductive bronze. Used with ground clamp to ground conductor to water pipe.

Category: Ground Clamps With Hub

Nsi 800ll2 800-300 Mcm 2 Screw Lug Mounting Hole 1 3/4 Center To Center

Category: 3-Conductor Aluminum Mechanical Lugs

10 Wire Polaris 600 MCM-6 AWG Insulated Multi-Cable Connector with Mounting Holes, Either Side Wire Entry Polaris Insulated Multi-Cable Connectors have wire entry ports on both sides of the connector to allow for access from either side. Mounting holes at each end of the connector allow for direct isolated mounting to the trough, panel or wireway. IPLMD Series connectors are insulated with high-dielectric strength plastisol. Molded for precise fit and supplied with removable access plugs over the hex screws. Eliminates the need for cover and taping. Abrasion and chemical resistant. UV resistant. Will not support combustion. Mounting holes will accept a 1/4" bolt for 3/0 AWG and a 5/16" bolt for 250 MCM and 350 MCM. UL Listed 486B Wire Connector. AL7CU. Cold temperature rated to -45 degrees C, rated 600V, 75 degrees C. Dual rated for use with copper and/or aluminum cables. Not recommended for fine-stranded, flexible wire.

Category: Single Sided Entry Wire Connector Blocks

NSI S12-14 12-10 AWG BARE SPA

Category: Non-Insulated Locking Fork Terminals

NSI L314 3 AWG CU COMPRESSION

Category: 1-Hole Long Barrel Copper Compression Lugs

6 Port 8 Mounting Hole Aluminum Dual Rated Transformer Lug 350 MCM - 6 AWG Aluminum Dual Rated Transformer Lugs are versatile and reuseable set screw connectors made of 6061T-6 aluminum alloy for superior electrical and mechanical performance. Two set screws per wire hole ensure an exceptional connection. Electro-tin plated for low resistance. For use with copper or aluminum conductors. Mounting hole spacing is NEMA 1-3/4". Meets or exceeds ANSI C119.4 Class A. Rated 600 Volts. Temperature Rating 90 degrees C.

Category: Transformer Lug Kits