"dhs1500ct diablo controls"

ICT .250KVA 208-600-85-130

Category: 250 - 450 VA Industrial Control Transformers

Explosion-Proof Photocontrol, Type Single Gang, Constructional Feature Explosion-Proof, Dust-Ignitionproof, Voltage Rating 120 V, Power Rating 1000 VA, Turn ON Light Level 1 to 3 FC, Temperature Rating -30 to 140 Deg F, Mounting 1/2 Inch Dead End, Enclosure Material Epoxy Powder Coated Malleable Iron Body, Epoxy Powder Coated Aluminum Cover, Enclosure Class I Group B C D, Class II Group E F G, Class III, Size 3 Inch W x 4.81 Inch D x 6.31 Inch H, Application Chemical and Petrochemical Plant, Refinery, other Process Industry, Current Rating 8.3 Ampere, Turn On/Turn Off Ratio 1:3

Category: Digital Lighting Photocells

Line Voltage Ceiling Mount Photocell, Low profile: Set/Off, Fade Rate: 30 Min, Demand Response: 75% (MFG Range 1-1600FC), Title 24 Compliant, ASHRAE 90.1 Compliant

Category: Daylight Photo Controls

IMT 156T3230A TRIPPERS (1 ON

Category: Time Switch Trippers

Pressure Sensing Momentary Air Switch, 3 Amp

Category: Time Switch Mounting Accessories

CH N2S2110MSR1EM N2S AND N2SC FS CORRSION-RESISTANT CNTRL STATIONS

Category: 2-Element Control Stations

AL1024ULACMCB Access Power Controller w/ Power Supply/Charger, 8 PTC Class 2 Relay Outputs, 24VDC @ 10A, FAI, 115VAC, BC400 Enclosure. Altronix AL1024ULACMCB converts a 115VAC 60Hz input into eight (8) independently controlled 24VDC Fail-Safe and/or Fail-Secure outputs with a total of 10A continuous supply current. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. This unit will route power to a variety of access control hardware devices including Mag Locks, Electric Strikes, Magnetic Door Holders, etc. These outputs will operate in both FailSafe and/or Fail-Secure modes. This unit is designed to be powered by one common power source (factory installed) which will provide power for both the board operation and locking devices, or two (2) totally independent power sources, one (1) providing power for board operation and the other for lock / accessory power. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the eight (8) outputs.

Category: 1-Phase DC Power Supplies

GED CR305X141B CONTROL CKT FUSE KIT

Category: Starter & Contactor Fuse Blocks

ABB AF140N4301113 NEMA SZ4 10

Category: IEC Contactors - 66-Over Amp

ABB 1SNK708011R0000 ZK6-3P FE

Category: 6mm Feed Through & Ground Terminal Blocks

C-H 14957H9 CNTL CIR LIMIT SW

Category: Safety Interlocks

LUT PJ2-2B-GIV-P02 PICO 2B BE

Category: Wireless Dimmers & Switches

LUT PJ2-2B-TSW-P02 PICO 2B BE

Category: Wireless Dimmers & Switches

LUT PJ2-2B-TMN-P02 PICO 2B BE

Category: Wireless Dimmers & Switches

PICO 2B BEDSIDE SCENE GBL

Category: Wireless Dimmers & Switches

C-H 10250T5B62-S104 10250T, P

Category: 1-Element Control Stations

Maestro Digital Fade Dimmer, 120/277V, 6A, Multi-Location/Single-Pole, 3-Wire Fluorescent Ballasts, Wireless Capable, Gray

Category: Wireless Dimmers & Switches

APP SLNP0RQ OFF-REMOTE SEL SW

Category: 2-Element Control Stations

EMERGENCY STOP PUSH BUTTON STATION

Category: 1-Element Control Stations

ACMCE1500N008

Category: 1 - 1.6 KVA Industrial Control Transformers

AA Battery Adapter For Pulse Impulse Exothermic Welding Control Unit

Category: Welding Ignitor Control Units

IMT PA102 REPLACEMENT THERMOS

Category: Time Switch Mounting Accessories

Replacement Plate Only for E1120, KM2ST-1G, and KM2SW-1G

Category: Time Switch Enclosures

PICO 2B ENTRANCE SCENE GLA

Category: Wireless Dimmers & Switches