Search results

Mounting Bracket for Evolution 8-Gang Floor Box

Category: Recessed Floor Box Service Fittings

2" IPS locking nipple for 525 and Multiplex Series fittings. 1 1/2" long. Finish - Anodized Aluminum

Category: Recessed Floor Box Service Fittings

Receptacle opening 1 3/8" [35mm]. Fits into any one (1) of the shaded areas shown.

Category: Recessed Floor Box Service Fittings

For use with 10" [254mm] diameter hole. All devices are recessed 4 1/2" [114mm} below the finished floor level. Unit ships complete with an all aluminum cover (assembled) designed to sit on top of finished floor surface (carpet, tile, wood, concrete or terrazzo). Covers are available in the following powder coated finishes: black (BK), gray (GY), nickel (NK), brass (BS) and aluminum (AL). The covers are also available in two 10ATCPB plated finishes: brass (PB) and satin chrome (SC).

Category: Recessed Floor Box Service Fittings

Has one 2" trade size knockout.

Category: Recessed Floor Box Service Fittings

Includes one (1) Ortronics Series II adapter and one (1) TracJack adapter.

Category: Recessed Floor Box Service Fittings

Communication bracket with Ortronics AB2TJ TracJack and ABS2 Series II adapters included. Accepts Ortronics workstation connectivity

Category: Recessed Floor Box Service Fittings

Device plate that will accept up to six (6) Extron Electronics MAAP style plates. For use in the center compartment only. Devices supplied by others.

Category: Recessed Floor Box Service Fittings

Receptacle opening 1 9/16" (40mm). For 8" poke-thru units only.

Category: Recessed Floor Box Service Fittings

FACE PLT 1/2IN OPNG 500 SERIES

Category: Recessed Floor Box Service Fittings

6A opening with communication adapter on one side. Accommodates Wiremold Open System communication modules. NOTE: Four-piece service fittings include: housing and base plate. Receptacles included when indicated in part number description. 525 Series Service Fittings have 27 cubic inches (442ml) of capacity. NOTE: Four-piece service fittings include: housing and base plate. Receptacles included when indicated in part number description. 525 Series Service Fittings have 27 cu. in. (442ml) of capacity.

Category: Recessed Floor Box Service Fittings

WMD EFB810-3/4-3/4 3/4IN / 3/

Category: Recessed Floor Box Service Fittings

<p>Installed either before or after concrete pour to create activation from duct. NOTE: Drill a 2 1/2'' (64mm) hole in concrete and a 2 1/4'' (57mm) hole in duct.</p>

Category: Recessed Floor Box Service Fittings

Exterior-gang pass through assembly. Designed to allow cables to pass through one (1) of the four (4) exterior-gang compartment locations.

Category: Recessed Floor Box Service Fittings

To connect S4000 Series Raceway with surface type panel boxes. Accommodates maximum wire capacity of S4000 Series Raceway. Separate C-shaped flange fits around raceway, covering any irregularities from cutting into box. Cut 4 3/4" x 1 3/4" [121mm x 44mm] hole in panel box.

Category: Recessed Floor Box Service Fittings

<p>Four (4) duplex KOs. One plate supplied with AC8850 Box. NOTE: AC8850 is a single-service box. Power plates cannot be used in conjunction with communication plates.</p>

Category: Recessed Floor Box Service Fittings

Adjusting ring (with three adjusting screws) for use with 437 Attaching Rings - power for brass fitting only. 3 25/32" (96mm) O.D.

Category: Recessed Floor Box Service Fittings

WM EFB8M 8-GANG MODULE ASSEMB

Category: Recessed Floor Box Service Fittings

1" IPS locking nipple for 525 and Multiplex Series fittings. 1 1/2" long. Finish - Anodized Aluminum

Category: Recessed Floor Box Service Fittings

Prewired snap-in 20A receptacle can be wired as standard duplex or isolated ground. Available only in black. See installation instructions with replacement receptacle for complete installation details.

Category: Recessed Floor Box Service Fittings

RFB4-4DB DEVICE PLATE W/EXTRON AAP

Category: Recessed Floor Box Service Fittings

RFB4-4DB DEVICE PLATE W/EXTRON MAAP

Category: Recessed Floor Box Service Fittings

Attaching ring for Source I (preset or afterset) zinc die-cast. 4" (102mm) O.D. 2 3/8" ring depth. Finish - Anodized Aluminum

Category: Recessed Floor Box Service Fittings

2" IPS to 1/4" Afterset Insert Finish - Anodized Aluminum

Category: Recessed Floor Box Service Fittings