Search results

Tile Flange, 1-Gang, Aluminum, Nickel. W x L: 3.48" x 4.524". For Use on: 880S1, 880M1, 880CS1-1, 880CM1-1 Floor Boxes in Tile Applications.

Category: Square / Rectangle Recessed Box Flanges

4-GANG RECESSED CAST IRON FLR BOX

Category: Recessed Compartment Boxes

Adjusting ring (with three adjusting screws) for use with 437 Attaching Rings - power for brass fitting only. 3 25/32" (96mm) O.D.

Category: Recessed Floor Box Service Fittings

One-gang pass through housing assembly. Designed to allow pass through of communication cables when no conduit is required. NOTE: When using on a 6ATCFF Furniture Feed unit, 1BHA (sold separately) is required.

Category: Poke-Through Mounting Plates

Includes 6" diameter poke-thru stem assembly with a disposable plate. Devices are recessed 3 1/4" (83mm) below floor surface. No cover assembly is included. For use with the following cover assemblies (purchased separately): 6CTC and 6CT Series. INCLUDED: For Side Compartments: Two (2) proprietary 20A Duplex Power Receptacles installed. For Center Compartment: One (1) 6ACT8A Mounting Plate, One (1) 6TRAC Mounting Plate, One (1) 6SER Mounting Plate. For Bottom Feed Compartment: One (1) 5BLH 1/2-Gang Pass-Through Blank Housing Assembly (Tunneling extends from the 5BLH to 575CHA so that power cables from the 20A duplex receptacle mounted on the left side of the poke-thru device are run into the junction box attached to the 575CHA.) , One (1) 1PTHA 1-Gang Pass-Through Housing Assembly, One (1) 575CHA 1/2-Gang 3/4" Conduit Housing Assembly (also includes junction box attached to the 3/4" conduit). NOTE: UL Fire Classified for up to 2-hour rated floors. Receptacles can be wired as a standard or isolated ground device.

Category: Assembled Poke-Through Units

Available in black (BK), gray (GY), ivory (VY), nonmetallic brass (BS), and nonmetallic aluminum (AA). Assembled with scrub water gasket. For use on tile or carpet floors.

Category: Poke-Through Cover Assemblies

4-INCH FURN FEED POKE-THRU ASSY BZ

Category: Assembled Poke-Through Units

1" IPS locking nipple for 525 and Multiplex Series fittings. 1 1/2" long. Finish - Anodized Aluminum

Category: Recessed Floor Box Service Fittings

WMD AV4005BK 2.0 USB

Category: Poke-Through Mounting Plates

WMD DQFP15UST-2A DUAL STAINLE

Category: Assembled Recessed Countertop Boxes

Combination Carpet and Tile Flange, 1-Gang, Powder-Coated Aluminum, Gray

Category: Square / Rectangle Recessed Box Flanges

Round Floor Cover, Diameter: 5-1/2 Inch, Single Service 3/4 Inch Opening, Device Type: Communication. Color: Bronze. For use in Carpet Applications.

Category: Round Recessed Box Covers

Flangeless Blank Cover Assembly, No Cut-Out, Color: Nickel, Material: Die-Cast Aluminum

Category: Square / Rectangle Recessed Box Covers

Floor Box Activation with Gray Flange

Category: Assembled Recessed Round Boxes

Holds four (4) Legrand AVIP or Extron Electronics MAAP devices. Device plate dimensions: 2.3" x 4.652" (58mm x 118mm).

Category: Recessed Compartment Box Device Plates

Blanking Top Plate. Diameter: 3-1/2 Inch, For use with: 3/4 Inch IPS, Stainless Steel

Category: Round Recessed Box Covers

WMD 8CREST 2G CRESTON PLATE

Category: Poke-Through Mounting Plates

W-mold S165b Fl Brass Pwr Sgl duplx

Category: Square / Rectangle Recessed Box Flanges

Floor Box Cover, 2-Gang, Non-Metallic, Cover Type: Open. Device Type: Duplex Receptacle. Color: Brown. Includes: Receptacle Plate, Receptacle Membrane, (2) 15 Amp, 125 Volt Receptacles, Carpet Flange, Round Attaching Ring/Adapter.

Category: Square / Rectangle Recessed Box Covers

Available in black (BK), gray (GY), painted brass (BS), and ivory (VY). NOTE: To abandon the RC4 Series Poke-Thru Device, the internal gasket, duplex receptacle, and communication modules must not be removed in order to maintain UL Classification. Also the stem must remain in the hole.

Category: Round Recessed Box Covers

<p>Faceplate with 6a mini adapter for Wiremold Open System CM2 communication modules.</p>

Category: Recessed Floor Box Service Fittings

Flangeless cover for use in tile installation. Die-cast aluminum assembly. Insert in lid allows for tile cutouts to match finished floor. NOTE: Add suffix “TR" to the end of the part number to indicate tamper-resistant cover assembly. Tamper-resistant versions are secured with a single tamper-resistant screw.

Category: Square / Rectangle Recessed Box Covers

Kit comes complete with adapter ring to secure into the boxes, Wiremold CM Series open system adapters (unloaded), Ortronics Series II, and TracJack adapters. Modular jacks and A/V connectors sold separately.

Category: Round Recessed Box Covers

WMD 6FFAFB-.5BP 6-INCH FF BOT

Category: Recessed Floor Box Service Dividers