"isr-250"

NSI NC-250-0 .250" X 3/8" NYL

Category: Cable Straps

Interval Timer, 60 Minute, White Twist Knob, 20 Amp, 250 Volt AC, with Hold, In-Wall Time Switch

Category: In-Wall Spring Wound Time Switches

NSI CP250 250 MCM CABLE ENTRY

Category: Capped Bushings

Insulated Multi-Cable Stacked Connector Block, Wire Entry Either Side, 600V, Number of Ports: 6, Wire Range: 6 AWG - 250 MCM, UV Rated, Abrasion and Chemical Resistant. Dual Rated for use with Copper and/or Aluminum Conductors.

Category: Dual Sided Entry Wire Connector Blocks

Compression Lug, Standard barrel, 2 Hole, 250 - 600 MCM, 1/2 Inch Stud, Aluminum With Tin Finish, Color Code Black, For USe With Copper or ALuminum Conductors

Category: 2-Hole Aluminum Compression Lugs

Insulated Multi-Cable Connector Block, Wire Entry Either Side, 600V, Number of Ports: 10, Wire Range: 250 MCM - 750 MCM, UV Rated, Abrasion and Chemical Resistant. Dual Rated for use with Copper and/or Aluminum Conductors.

Category: Dual Sided Entry Wire Connector Blocks

Heavy Duty 1 Cable Parallel Ground Connector for 1/2-3/4in 250 MCM-2/0 AWG. Pipe Made of high-copper-content alloy for grounding to 1/2" - 1" ground rods and ground pipes from 1/4" - 3 1/2" in parallel or 90 degree position. Suitable for direct burial in earth and concrete. Nuts and lockwashers are silicon bronze.

Category: U-Bolt Ground Clamps

NSI IFL12-250-3N-BULK 12-10 A

Category: Wire Disconnect Adapters

NSI IFL22-250-3N 22-18 AWG IN

Category: Wire Disconnect Adapters

NSI IM16-250-3N-S 16-14 AWG F

Category: Wire Disconnect Adapters

NSI IM16-250-3N-P 16-14 AWG F

Category: Wire Disconnect Adapters

Heavy Duty Copper C Tap Grounding Connector for 500 to 250 MCM APPLICATIONS: Copper "C" Taps ensure positive, all-around compression with low-resistance and high pull-out values. Made of high conductivity copper, they satisfy the requirements of NEC250-81 and 250-91 for connecting to the grounding electrode system. Rated 600 Volts.

Category: C-Tap Press-On Lugs

12-10 AWG Nylon Insulated Flag, 50/Pack

Category: Wire Disconnect Adapters

NSI IF16-250-3N-S 16-14 FULLY

Category: Wire Disconnect Adapters

4 Wire Polaris 250 MCM-6 AWG Insulated Multi-Cable Connector with Mounting Holes, Either Side Wire Entry Polaris Insulated Multi-Cable Connectors have wire entry ports on both sides of the connector to allow for access from either side. Mounting holes at each end of the connector allow for direct isolated mounting to the trough, panel or wireway. IPLMD Series connectors are insulated with high-dielectric strength plastisol. Molded for precise fit and supplied with removable access plugs over the hex screws. Eliminates the need for cover and taping. Abrasion and chemical resistant. UV resistant. Will not support combustion. Mounting holes will accept a 1/4" bolt for 3/0 AWG and a 5/16" bolt for 250 MCM and 350 MCM. UL Listed 486B Wire Connector. AL9CU. Cold temperature rated to -45 degrees C, rated 600V, 90 degrees C. Dual rated for use with copper and/or aluminum cables. Not recommended for fine-stranded, flexible wire.

Category: Dual Sided Entry Wire Connector Blocks

NSI IF16-250-3N-BULK 16-14 AW

Category: Wire Disconnect Adapters

NSI M16-250-3V-S 16-14 AWG MA

Category: Male Non-Insulated Wire Disconnects

NSI IFL16-250-3N 16-14 INSULA

Category: Wire Disconnect Adapters

NSI IFS12-250-3N-BULK 12-10 A

Category: Wire Disconnect Adapters

22-18 AWG, .250 x .030 Tab Nylon Fully Insulated, 50/Pack

Category: Wire Disconnect Adapters

1 Port Aluminum Lug 250 MCM - 6 AWG Aluminum Single Lugs are versatile and reuseable set screw connectors made of 6061T-6 aluminum alloy. Electro-tin plated for low contact resistance. Suitable for use with both copper and aluminum conductors. Temperature Rating 90 degrees C. Rated 600 volts (2000V max. per UL486B). UL 486A/B Listed. .

Category: 1-Conductor Aluminum Mechanical Lugs

NSI 250-3MFM .250 X .32 BARE

NSI HTSF16-250-3-P 16-14 AWG

Category: Female Non-Insulated Wire Disconnects

NSI F16-250-3V-S 16-14 AWG VI

Category: Female Vinyl Insulated Wire Disconnects