Search results

Used to support the 6x4 and 4x4 systems attaching to any 3/8" (9.5mm) x 1 1/2" (38.1mm) or 3/8" (9.5mm) x 2" (50.8mm) ladder rack rail. Adjustable to nine incremental positions from 4" (101mm) to 12" (305mm) above or below the ladder rack. No threaded rod

Category: Mounting Hardware & Brackets

FiberRunner Threaded Existing 1/2 Inch Rod Bracket, Black

Category: Mounting Hardware & Brackets

FiberRunner QuikLock New Threaded Rod Bracket

Category: Mounting Hardware & Brackets

Provides secure, accessible route for cables spilling out from vertical tee to rack mounted equipment. Kit includes 6ft length of 4x4 capacity hinged duct, 6ft length of 4x4 hinged duct cover, one end cap for 4x4 hinged duct, three FZBA1.5X4 adjustable Z

Category: Drop-Offs, Spillouts & Outlets

Used to support the 12x4 system by spanning two threaded rod drops that are 18in apart. Can be installed from above or below. Bracket is secured to each threaded rod with two nuts. The pre-assembled slide clamps enable fast assembly to channel. Use 7/16in

Category: Mounting Hardware & Brackets

Used to support the 12x4 system from existing threaded rod installations. Bracket is secured to threaded rod with two split nuts. The pre-assembled slide clamps enable fast assembly to channel. Use 7/16" nut driver on slide clamps, For 5/8" Threaded Rod.

Category: Mounting Hardware & Brackets

Used to support the 6x4 and 4x4 systems attaching to the top of an equipment rack. Contains hardware to mount to the top of EIA/TIA equipment racks. No threaded rod required. The pre-assembled slide clamps enable fast assembly to channel. Use 7/16" nut dr

Category: Mounting Hardware & Brackets

The fiber mounting FiberRunner® QuikLock™ Threaded Rod Trapeze Bracket for Wyr-Grid® 12" (305mm) width is used to support a FiberRunner® 4x4 and 6x4 Channel above or below the Wyr-Grid® 12" Pathway using the same 1/2" or 12mm threaded rod used to support

Category: Mounting Hardware & Brackets

Used to support the 6x4 and 4x4 systems from existing threaded rod installations. Bracket is secured to threaded rod with two split nuts. The pre-assembled slide clamps enable fast assembly to channel. Use 7/16" nut driver on slide clamps, For 5/8" Thread

Category: Mounting Hardware & Brackets

Used to support the 6x4 and 4x4 systems from any new threaded rod extending down directly from the ceiling, grid, or ladder rack system. Two position height adjustments to accommodate system with or without hinged cover. Bracket is secured to threaded rod

Category: Mounting Hardware & Brackets

The fitting transitions from ADC's 12x4 FiberGuide System to the Panduit 12x4 FiberRunner® System. It is black and made of metal. Attachment hardware is included.

Category: Couplers & Joiners

Fitting that transitions from ADC's 4x4 FiberGuide System to 4x4 FiberRunner® System. Fitting has a black finish and is made from metal. Attachment hardware is included.

Category: Couplers & Joiners

Used to support the 6x4 and 4x4 systems from below with new threaded rod. Bracket is secured to threaded rod with two nuts. The pre-assembled slide clamps enable fast assembly to channel. Use 7/16in nut driver on slide clamps. Also can be secured directly

Category: Mounting Hardware & Brackets

T-bolts can be used for additional attachment when securing FiberRunner® Channel to mounting brackets. For example, a T-bolt can be inserted thru a 12x4 mounting bracket and positioned within the center rib structure on the underside of 12x4 channel. By t

Category: Mounting Hardware & Brackets

Used to support the 12x4 system, dual 6x4, or dual 4x4 systems attaching to the top of cabinets. Adjustable from 4 1/4" (108mm) to 12" (305mm) allowing runs to be leveled over uneven cabinet heights. Bracket is secured to the cabinet frame with through bo

Category: Mounting Hardware & Brackets

Used to support 12x4, 6x4, and 4x4 systems attaching to the top of the 19" wide version of the Panduit NF4PR84 4 post rack. Contains all hardware required to assemble bracket to the top of the 4 post rack. Bracket accepts 5/8" threaded rod (not included).

Category: Mounting Hardware & Brackets

Used to support the 6x4 and 4x4 systems by spanning two threaded rod drops. Can be installed from above or below. Bracket is secured to each threaded rod with two nuts. The pre-assembled slide clamp enables fast assembly to channel. Use 7/16in nut driver

Category: Mounting Hardware & Brackets

Used to support the 6x4 and 4x4 systems by attaching to underfloor pedestals. (Contains all necessary hardware.) Use on pedestals up to 1" in diameter. The pre-assembled slide clamps enable fast assembly to channel. Use 7/16" nut driver on slide clamps.

Category: Mounting Hardware & Brackets

Used to support the 6x4 and 4x4 systems from any new threaded rod extending down directly from the ceiling, grid, or ladder rack system. Two position height adjustments to accommodate system with or without hinged cover. Bracket is secured to threaded rod

Category: Mounting Hardware & Brackets

The fitting attaches any 6" x 4" (150mm x 100mm) FiberRunner® fitting or channel to the 4" x 4" (100mm x 100mm) Fiber-Duct™ Channel S4X4YL6 or E4X4YL6. It is yellow and made of ABS plastic. It includes a solid cover.

Category: End Caps & Reducers

7/16" nut driver for use with the FiberRunner®, GridRunner™, and Wyr-Grid™ Systems.

Category: Storage Loops, Tubing & Tools

Used to support the 6x4 and 4x4 systems attaching to the top of cabinets. Adjustable from 4 1/4" (108mm) to 9" (229mm) allowing runs to be leveled over uneven cabinet heights. Bracket is secured to the cabinet frame with through bolts (not included). The

Category: Mounting Hardware & Brackets

Used to carry the cables horizontally throughout the system. Accepts hinged cable retainers FRCR4BL, hinged cover FRHC4YL2 or split hinged cover FRSHC4YL2. Use QuikLock Couplers FRBC4X4YL to attach channel and/or fittings.

Category: Straight Sections

Optional snap-on hinged cover for channel FR12X4BL6. Can be folded down for height restricted areas.

Category: Covers & Retainers