1-Piece Raceway & Accessories

Office furniture corner raceway base. Used to terminate low voltage data cabling in the corner at the intersection of modular office furniture panels. Accepts 70mm standard faceplates. Available in 6' lengths.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Two cubicle drop fitting. Allows the transition from office furniture raceway run horizontally along partition wall to office furniture corner raceway mounted vertically in two cubicles at the intersection of partitions. Fitting maintains 1in minimum bend

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Raceway Wall Entrance FittingWall entrance fitting. Allows entry from wall to office furniture raceway run horizontally along partition walls. Fitting includes bend radius protection and trim plate to cover wall opening. Requires minimum wall opening of 4.5in W x 3.0in H (114.3mm x 7

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Office Furniture Raceway Four Cubicle DropFour cubicle drop fitting. Allows the transition from office furniture raceway run horizontally along partition wall to office furniture corner raceway mounted vertically in four cubicles at the intersection of partitions. Fitting maintains 1" minimum ben

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Office Furniture Corner Raceway End CapCorner raceway end cap fitting. Opening allows cord passage through fitting such as monitor and keyboard cables. Supplied with adhesive tape, Office Gray.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Two cubicle drop bypass fitting. Allows the transition from office furniture raceway run horizontally along partition wall, around existing furniture pole, to office furniture corner raceway mounted vertically in two cubicles at the intersection of partit

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Office Furniture Raceway Double Spill-Over FittingDouble spill-over fitting. Fitting is used to spill over both sides of the furniture partitions at the same location. Incorporates a built-in, yet removable end cap that eliminates the need for additional raceway and fittings to terminate the pathway. Off

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Office Furniture Raceway Right Angle FitRight angle fitting. Used to join sections of office furniture raceway at 90° flat junction. Supplied with adhesive tape, Office Gray.

Category: 1-Piece Non-Metallic Raceway Elbows

Office Furniture Raceway Outside CornerOutside corner fitting. Used to join sections of office furniture raceway at outside corner. Supplied with adhesive tape. Office Beige.

Category: 1-Piece Non-Metallic Raceway Elbows

Four cubicle drop bypass fitting. Allows the transition from office furniture raceway run horizontally along partition wall, around existing furniture pole, to office furniture corner raceway mounted vertically in four cubicles at the intersection of part

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Tee divider insert for TG-70 Raceway

Category: 1-Piece Non-Metallic Raceway Tee Fittings

Outside corner fitting – non-adjustable. PVC, White, Used to join sections of TG raceway at inside corners.

Category: 1-Piece Non-Metallic Raceway Elbows

Transition fitting from TG to T-45. Provides a tee transition from TG raceway to T-45 and LD series size 5 and 10. Use with RF5X3 reducer fitting to transition to LD series size 3.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

Office Furniture Raceway Snap-on VerticaSnap-on single gang vertical sloped communication faceplate. Accepts up to four PANDUIT® Mini-Com® Modules (not included). No additional mounting hardware required. TIA/EIA-606-B compliant.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Power rated right angle/entrance end fitting for use with LD3, LDPH3, LDS3, LD5, LDPH5, LDS5, LD10 and LDPH10 raceway. Use CA3 or CA5 adapters for LD3/LDPH3/LDS3 and LD5/LDPH5/LDS5 profile raceway; adapters not required for LD10 and LDPH10 raceway.

Category: 1-Piece Non-Metallic Raceway Elbows

Outside corner fitting. Used to join sections of TG raceway at outside corners. Fittings adjust from 85° to 135° to adapt to non-square corners. Electric Ivory.

Category: 1-Piece Non-Metallic Raceway Elbows

Tee fitting. Used to join sections of TG raceway at tee intersections, Electric Ivory.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

Inside corner fitting. Used to join sections of TG raceway at inside corners. Fittings adjust from 85° to 135° to adapt to non-square corners.

Category: 1-Piece Non-Metallic Raceway Elbows

Attaches to 4x4 channel and/or fittings to create a 90° upward angle from a straight horizontal run. Used with outside vertical 90° angle fitting FROVRA4X4OR to change level of a straight horizontal run. Includes split cover.

Category: 1-Piece Non-Metallic Raceway Elbows

Drop ceiling/entrance end fitting for use with LD5 raceway, Electric Ivory, ABS, Length 3.42 in, Width 1.6 in.

Category: 1-Piece Non-Metallic Raceway End Fittings

Snap-on single gang horizontal sloped communication faceplate. Accepts up to four PANDUIT® Mini-Com® Modules (not included). No additional mounting hardware required. TIA/EIA-606-B compliant.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Attaches to 6x4 channel and/or fittings to create a 45° downward angle from a horizontal run. Used with inside vertical 45° angle fitting FRIV456X4OR to change level of a straight horizontal run. Accepts optional split cover FROV45SC6OR.

Category: 1-Piece Non-Metallic Raceway Elbows

Corner raceway end cap fitting. Opening allows cord passage through fitting such as monitor and keyboard cables. Supplied with adhesive tape, Office Slate.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings